Home > Dell Optiplex > Dell Optiplex GX200 Problems

Dell Optiplex GX200 Problems

I have a Dell Optiplex Gx280 and it won't start, an amber light is flashing in the power button. Possible Basic Input/Output System (BIOS) or driver update required. For information on how to disable power management, refer to the NIC documentation. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. check over here

The workaround for this issue is to increase the jitter tolerance on the Catalyst 6000 and 6500 switches for 10/100 ports to 3.1 seconds. About a year ago, I had someone come in and install a wireless card. Catalyst 2950 and 3550 Switches This table lists several known issues found on the Catalyst 2950 and 3550 switches. The 0 in the Bits column refers to the programmable register address, and the decimal number after the 0 refers to the bit placement within the 16-bit register. http://en.community.dell.com/support-forums/desktop/f/3514/t/18077299

Thanks for your help. When you troubleshoot link up/down issues, disable this feature. Dell OptiPlex GX260 PC Desktop Optiplex 560 Power Intermittent Try updating the BIOS.

If you increase speed and move the link partner to full-duplex, it minimizes this occurrence. See technical document TID2227 at Asanté support website. 3Com 3C574/575 PCMCIA 10/100 Extremely slow performance when operating at 10 MB. The workaround is to disable the packet buffer test. Recapping fixes them and they go right back out, I haven't had one come back again in 2 years!

The motherboards were manufactured with an Intel Chipset that are incompatible with Cisco switches and Netgear hubs. Dell OptiPlex GX260 PC Desktop Windows XP CD cannot be detected in Dell Optiplex gx260 I have the same problem with my windows 2000 cd \015\012But I found out that you Contact vendor support for more information. http://www.electronic-servicing.com/dell_optiplex_gx200_pc_desktop/q1089841-problem_booting_dell_optiplex_gx200 The Gigabit autonegotiation negotiates flow control, duplex mode, and remote fault information.

Nov 13, 2008 #17 pjamme TS Enthusiast Posts: 208 Blown Capacitors tb421ny, It has been many years since I soldered. The workaround is to disconnect and reconnect the cable that connects the workstation to the switch port. The exact same way you feel if you touch the terminals of a 9V battery with your tongue. Please join our friendly community by clicking the button below - it only takes a few seconds and is totally free.

Disable all power management functions. About a year ago, I had someone come in and install a wireless card. When the NIC is disabled for power management, it drops the link to the switch. CSCdk32984 (registered customers only) 4.2(2) The 48-port, 10BASE-T Ethernet module (WS-X5012) incorrectly drops valid frames with dribble bits (extra bits added to frames by some end stations and transceivers).

You'll be able to ask questions about your motherboard or chat with the community and help others. http://fixmyacer.com/dell-optiplex/dell-optiplex-960.html This problem usually only represents one percent to two percent of the total traffic. Moot point anyway as we were purchased by a UK group and are now an HP house. this was the only sign of issues up until it really started acting up.

The command must be issued for a single port at a time. Notable slow performance. Dell Optiplex GX200 The link flaps when it connects to a Dell Optiplex GX200 PC (Intel Pro 10/100). this content I did both things but it still does'nt power up.

Customers report AppleShare IP servers slow down and eventually crash over time. Join the community here. Table 5—Possible Causes for Incrementing CatOS Counters Counter Possible Cause Delay Exced Severe problem with the switch.

Rcv-Err This is an indication that the receive buffer is full.

Motherboard Forums Forums > Motherboard Manufacturers > Dell > Dell Optiplex GX200 Hard drive problem Discussion in 'Dell' started by mikehende, Sep 7, 2006. Contact vendor technical support for more information. Refer to this document for information on the counter displayed: show counters Command Documentation For additional information about the Cisco IOS Software show interfaces command counters, refer to: show interfaces Command Motherboard Forums Forums > Motherboard Manufacturers > Dell > Forums Forums Quick Links Search Forums Recent Posts Members Members Quick Links Notable Members Current Visitors Recent Activity New Profile Posts Menu

I followed the same procedure but it didn't work this time. In order to troubleshoot this issue, try to manually configure the switchport to 100 Mbps, half-duplex. Is there physical connectivity? have a peek at these guys Refer to Using PortFast and Other Commands to Fix Workstation Startup Connectivity Delays for more documentation with regard to this configuration change.

Contact Apple technical support. All of ours have been 270s so far. Know the operating system and the NIC driver version. Catalyst 8500 interface defaults to half-duplex mode when the peer is incapable of negotiation.

I'm logging on as the same user as I created the >> images with!>>>> Any help much appreciated>>>> Ben>>>> Can't find your answer ? A few months ago I noticed it was loose so I opened the machine, and put the card back in place. Single Collisions Single collisions are the number of times the transmitting port had one collision before successfully transmitting the frame to the media. The install went fine, however when I tried booting the >> client PCs I kept getting an error>> PXE-E53 No boot filename received.>> After googling this error I found that you

Asanté GigaNIC 1064SX PCI Card-Macintosh Slow performance with AppleShare IP servers and PCI Ethernet cards. Hope this can help... Dismiss Notice TechSpot Forums Forums TechSpot Core CPUs and Motherboards Today's Posts Dell Optiplex GX280 won't start, amber lightflashing ByDarkJP · 41 replies Aug 1, 2008 Page 1 of 2 1 Because of these recent issues, the use of autonegotiation is regarded as a valid practice.

CSCdr37645 (registered customers only) 4.5(8), 5.5(2), 6.1(1) An invalid packet with a length of less than 64 bytes received on a 10/100 port causes both the Runts and FCS-Error counters to Main Sections Technology News Reviews Features Product Finder Downloads Drivers Community TechSpot Forums Today's Posts Ask a Question News & Comments Useful Resources Best of the Best Must Reads Trending Now Apple Macintosh, Power Macintosh G3, and Powerbook G3 Unable to set speed and duplex of built-in Ethernet interface manually. I'm using an Optiplex 210 that's glitchy patty, Aug 8, 2006, in forum: Dell Replies: 6 Views: 953 Jay B Aug 9, 2006 Adding a hard drive to Optiplex 170L Ron

Thanks for your help. The > IDE1 controller has the original drive with the WD [IDE] drive which > has NT on it. The time now is 02:31 AM. I felt the same discharge the second time I followed the procedure.Click to expand...

Oct 23, 2008 #14 seanc TS Rookie Posts: 88 pjamme said: ↑ Not so my friend. Rcv-Err This is an indication of excessive output rates of traffic.